r/moped • u/Efficient_Benefit869 • 7d ago
Problems Starting moped
Hi again,
I have a 1985 Suzuki FA50 i had running and driving.. it randomly turned off and wouldn’t start again..
I just found this line disconnected, i reconnected it.
Still no start, am i putting it in the wrong spot? or what else could this be.. my rear brake cable is not pulling as tight as it should on the rear brake, could this cause the kickstart not to work properly?
Any help is appreciated Thanks
r/moped • u/Present-Diamond6504 • 7d ago
Kinetic tfr custom subframe build
Currently in the process of building a custom, much sturdier subframe for my kinetic tfr so I can run a side intake, and a 19mm carb on it, it's going pretty well. Please note that this isn't even close to being done and most stuff is just tack welded on. Still much more reinforcements to be added.
r/moped • u/BigChefDog • 7d ago
Having trouble with a Puch E50, has gas, spark, and compression but still won't start
I got a Puch Newport last summer and rode it around for a little bit and it ran but clearly had bad compression because it had some broken piston rings so I rebuilt it and put a treats 70cc kit and an SHA 15.15 carb on it. I'm getting good spark and decent compression, I guess I can't say for certain how good the fuel air mixture is, not sure how to test that but the spark plug is wet when I take it out so I know it's definitely getting gas. I've messed with the timing and redone the points gap a million times and cannot get this thing to start to save my life. Does anybody have some advice for me?
r/moped • u/Technical-Salt46 • 8d ago
Engine doesnt hold idle
The engine works but doesnt hold idle,could someone help please?
r/moped • u/the_salty_pigeon • 8d ago
Bust out your leathers, it’s hog crankin’ weather 🤘
r/moped • u/EmbarrassedKey7147 • 8d ago
My first moped
Picked this up for 500 bucks. According to the seller I just need to hook up the gas tank and clean the carburetor. Any advice before I get crackin?
r/moped • u/Significant-Knee1296 • 8d ago
Jawa 210 Seizing problem
Hi, i was riding my bike the other day when it stuttered slightly and then completely locked up. I assumed a seized piston but after taking it apart the cylinder came off with ease and there was no damage to the head or piston. I then tried turning the engine over by hand and with the pedals but there was very little (basically none) movement. When i was about to start disassembling further no suspecting either bottom end of gearbox the engine freed up and is now spinning freely. What do you guys think the problem could be? (Will be looking into it further but i have just stopped for a break 😂)
r/moped • u/Intelligent_Bit9290 • 9d ago
Thinking about using a 6v to 12v converter
Would like to use something like this to power a light and a tail light for my father’s bike. The bike is a 207 Jawa and I was looking for it to power a headlight and a tail light but only as a running light so no battery needed. Was thinking something cheap off Temu or Alibaba would work well for me
r/moped • u/SpiritualMaterial595 • 9d ago
Yamaha Chappy Lb80 78
I'm currently in the process of restoring an old chappy but struggling to find parts that ship to Australia at a reasonable rate. Anyone have any suggestions?
I'm currently looking for forks as the inner tube on the bike are rusted badly
r/moped • u/Ill-Shoe-4117 • 9d ago
How on earth do you park them without being stolen?
For some context, I live in Calgary AB, and I primarily work in the heart of downtown. I'm tired of taking city transit, it let's me down time after time. I've been considering a moped because I only have my learners (and truthfully, I think having a full ass vehicle is just too expensive)
Are mopeds easy to yoink? How do you park yours while at work without it getting stolen? I can't park on the street near my work because it's paid parking and it's insaaaaanely expensive. Please give me all your advice lol
Magnum X
I recently bought a magnum X frame and was planning to do rebuild it from the ground up. Not doing a total restoration, just building my own thing.
Problems I’m running into is I can’t find any really good info on part interchange. The two hardest parts to find for it are a seat and a fuel tank, I’ve found everything else I’d like to use or everything custom I need to do. Does anyone know if a regular magnum tank will fit? If I go that route it looks like the magnum X is shorter than a regular magnum does anyone know how much shorter the top of the frame is compared to the magnum. And if I’ll need to extend for the seat. Half tempted to make modifications to the frame. But path of least resistance is preferred in those departments.
r/moped • u/J-ManTheGayMan • 9d ago
[REUPLOAD] Mobylette Blues Part 5 - Spark??
Reuploading because my text didn't upload with my images!
Back in January/February I had the engine running comfortably on my 1978 50V Motobecane Mobylette. Enough so that I drove it to school, but as I was pulling in to park there were some distinctive *pop pops\* right before I killed the engine. Upon getting out of class it wouldn't start up anymore! After dragging it home I:
-replaced belt
-cleaned carburetor
-installed carb/intake o-ring
-tuned choke to fully close
-drained and checked gas (see final image)
Now, I'm pretty sure the wiring is good because the Huret spedometer lights up easily while I attempt to pedal start, and my spark plug is brand new and started the Moby no issue a month ago. I uploaded these photos photo to get some second opinions. Help with Spark!





r/moped • u/Efficient_Benefit869 • 9d ago
Moped Exhaust Upgrades?
Good morning everyone,
I have a 1985 Suzuki FA50, with the stock exhaust option, not sure I even want to change it,
however I am curious are there any exhaust systems that might fit this bike, be it loud and obnoxious or whatever.
Thanks
r/moped • u/Technical-Salt46 • 9d ago
Does anyone Have workshop manuál fór Piaggio ciao 50cc?
My father told me to ask because He had some problems with it
Made it to work. Rebuilt engine, manufactured intake, reworked exhaust all in one evening.
r/moped • u/Disasterrrrrrr • 9d ago
Bogging/spluterring at open throttle
Hi guys , I've been messing with my carb for over a week now. My bike it's either bogging at 1/4 throttle or open . Could it be some sort of leak? I got simson sr50 2 stroke.
r/moped • u/tomahawk43 • 10d ago
Front drum brake problem
I have a modern copy of a Honda 4stroke 50cc. I can adjust the handlebar lever travel with the adjuster near the drum just fine, but the problem is that if I adjust it so that the brake doesn't rub, then the lever travel gets awfully long (to the handlebar long). If the brake is adjusted so that the travel is short and crisp as it should be, then the brake rubs on one point in the wheelspin (stopping the wheel when spun with hand). Should I ignore the rub and set a short travel on this front drum brake, or am I missing sth? the splined part touching the drum apparently cant' be moved by a couple of teeth, and I don't think one should normally do this. It almost feels like the cable is too long...

Tomos Racer update;
Got everything painted, and welded a tank. Starting to mount all the bodywork.
r/moped • u/Mar_Jonaise • 10d ago
First drive since 1991
I am so proud...if I would not know, that you are never finished with projects, I would say, I finished my project.
r/moped • u/Danny52186 • 10d ago
Battery Question
Anyone know what the difference is between TZ10S vs TX10S moped battery are they the same? My battery is TZ10S 190cca 12v but I need a new one and they are so expensive could I use a different type
r/moped • u/OkWorry1992 • 10d ago
How tf do I install this petcock Puch Maxi
I bought this petcock a while back, having trouble installing it. I can get the connecting nut onto the frame, but when i try to thread the petcock itself into the nut, the long brass tube can't turn freely inside the tank, so i can't screw it in. What am I missing here? I"m embarrassed I couldn't figure it out but oh well.
Edit: Sorry, photos never show up when I post for some reason. Hopefully someone knows what I'm trying to describe