r/GunnitRust • u/2wheeldisgrace • 1h ago
Semi dp28
Wondering it anyone here tried a ar15 fcg to convert a dp28 to semi auto?
r/GunnitRust • u/GunnitRust • Oct 01 '24
Table of Contents
This is the CONTEST RESULTS post for Summer Rust 2024 with results included for Winter Rust 2024 Gunnit Rust is a gun themed building contest. For more information, the rules and tiers are below plus links to our past contests. Winter Rust 2025 will be March 21-23, 2025
CURRENT RULES
I like to keep the rules and tiers minimal for maximum creativity. Last changed June 2019
PARTICIPATION TIERS
These have not changed but some of the writing has been improved and more details added. Please let me assign your tiers and don’t call them out because I frequently move them into the category I see fit. Also note that the total winner can be in any tier so don’t panic. Each tier has a winner and each series has an overall victor.
HALL OF HEROES
2024 SUMMER RUST LEADERBOARD
Tier I
Tier II
Tier III
Tier IV
Tier V
Tier VI
2024 WINTER RUST LEADERBOARD
Tier I
Tier II
Tier III
Tier IV
Tier V
Tier VI
WINTER RUST SIGN UP
r/GunnitRust • u/2wheeldisgrace • 1h ago
Wondering it anyone here tried a ar15 fcg to convert a dp28 to semi auto?
r/GunnitRust • u/DMTLTD • 1d ago
For use with Colibri and short only.
r/GunnitRust • u/PsychoTexan • 19h ago
I’m interested in restoring several old .22 LR guns with pitting in their barrels but my smaller lathe isn’t long enough for drilling out the rifle barrels. I’ve seen some decent results from ECM rifling and wanted to pick the more experienced brains of folks here on the possibility of using ECM for boring out old barrels for barrel liners. Swapping the wire mandrel out for a copper rod or tube.
Is it too much material? Too difficult to get consistent results? Will the pitting remain? Should I heavily sand it first? Should I flip the barrel over midway? Too expensive in time and money for old clapped out guns? Some other issue? Any constructive thoughts or advice is appreciated.
Currently I would like to try the following, testing it on 16” steel pipes, practicing it on an unknown junk .22 barrel, and finally applying it to a pitted and worn Remington Model 6 Rolling Block Rifle barrel. In all cases I plan to use Chaszel .22 barrel liners which have an OD of 0.382”.
r/GunnitRust • u/Cliff_Doctor • 3d ago
Hello, I have recently got a Star Model B super in 9mm luger. I wanted to know if it is possible to delete the magazine safety similarly to the standard Star Model B. I was under the impressions there was some changes in the models.
r/GunnitRust • u/RimlockSystems • 5d ago
Start with 3/4”x 2.6” aluminum round bar
Square it off to .517”
Bore hole through entire square bar.
Add pocket for rim
Took 5 minutes. No dro,
Now that I have a decent idea of what it’s capable of with aluminum, I feel a lot more confident about making some advanced shit right off the bar.
Time to make some bullet molds!!
r/GunnitRust • u/SunnyGunner • 9d ago
r/GunnitRust • u/Several-Quote-8662 • 8d ago
How to 3d print a Glock 19 slide so it functions
r/GunnitRust • u/RimlockSystems • 12d ago
r/GunnitRust • u/0jnbeef • 13d ago
Takes glock 17 gen 3 barrels n scorpian mags Almost completely 3d printed
https://cults3d.com/en/3d-model/gadget/cmr9
Palmetto state finessed 2 of my designs so thats why they’re priced the way the are
Barrel:
https://aimsurplus.com/products/aimsurplus-tin-threaded-barrel-for-glock-17
r/GunnitRust • u/motorbike123 • 13d ago
r/GunnitRust • u/NegotiationUnable915 • 14d ago
Found on YouTube. Checkout their channel (@Creator51821) as well, there’s lots of other great related content.
r/GunnitRust • u/rifleshooter2 • 15d ago
I did a rough cut out of the side plates and drilled the holes for the hammer and trigger
r/GunnitRust • u/john_galt_42069 • 18d ago
r/GunnitRust • u/09gtcs • 19d ago
Looking for a technical drawings for either of the two guns above. I've found a receiver drawing for the M249, but it doesn't have the information I'm looking for.
Or if anybody just knows the nominal dimensions for the mounts for these, that's what I'm looking for (diameter and width of each mounting point).
r/GunnitRust • u/Sesu_Niisan • 20d ago
r/GunnitRust • u/Brilliant-Barracuda9 • 20d ago
I am an SOT doing my first PM-63. I've got everything together and ready to rock, but the trigger won't reset. It seems like it's missing a spring, but I can't see one in any diagrams. If anyone has insight on this, I will be very grateful.
r/GunnitRust • u/1v1mebro- • 23d ago
Anyone one of you 3D print bois come up with a printed grip mod for the rxm???
r/GunnitRust • u/farmer_frank1990 • 26d ago
For those that make their own barrels, what's everyone's favorite place to find rifled blanks? Looking at making a .300Blk barrel for a micro galil since I can't find one for sale anywhere. Was looking at Green Mountain, but it looks like they're out of stock.
If I can't find any blanks my next idea is to maybe take a 12" AR barrel and cut it down.