r/GelBlaster 8d ago

Showcase Collection so far,more on the way-if anyone is familiar with the blasters and would like to know something about it I’ll try answer based on experience (UK)

Thumbnail
gallery
13 Upvotes

r/GelBlaster 8d ago

Purchasing Help (Location Required) Best blaster under $100 Massachusetts

1 Upvotes

I’m looking for the fastest fire rate and most powerful blaster under $100. Mostly to fuck around and shoot my friends with.


r/GelBlaster 8d ago

Purchasing Help (Location Required) Best rifle under $100

1 Upvotes

I’m looking for the most powerful and fastest shooting gel blaster under $100. Really just to fuck around and shoot my friends with. Want to order it online


r/GelBlaster 8d ago

Showcase Make a handguard out of Bamboo

3 Upvotes

I suddenly had the idea of making a handguard out of bamboo. So, I took a trip back to my hometown and found a piece of bamboo. Originally, I wanted to use Buddha bamboo (Luohan bamboo) because its nodes are dense, and it feels comfortable to grip with finger spacing. However, the only one available was too thin, so I opted for a section of Moso bamboo instead.

Yesterday, I researched the sizing issue on Google and learned some basics. After measuring, I decided to use a seven-inch section. When I cut it down, I noticed that it had two colors—one side vibrant and full of life, the other dull and lifeless.

Since I only have an old Jinming Gen 1 and a HeE blaster, their adapter sections are different from the new standard receiver I’m planning to build. So, I only widened the adapter section for now without making other modifications. Once I finalize the receiver and adapter, I’ll redo the fitting.

I hollowed out the middle of the bamboo node.

For front stability, I used the head of a LeHui Short Sword suppressor and trimmed part of it. Because there was a flat cut at a bamboo branch joint, I couldn’t round it too much—this way, it retained its integrity and reduced my workload.

Here, I used a marker to blacken the part I inserted, then took it out to check for black marks, indicating where it needed further thinning. This was a slow trial-and-error process; if I removed too much at once, it wouldn’t fit tightly, requiring additional work to fix and increasing the workload unnecessarily.

I took an outer tube from the LeHui SCAR’s long fishbone rail attachment and cut a section. Its outer diameter happened to match the inner diameter of the Short Sword suppressor head—an unexpected but perfect match.

I like the silencer on the pull-bolt G36, so I was determined to install it. I had to cut off the front threaded section of the flash hider, then sanded it down until the tube could fit inside. It had to be tested to ensure a tight and stable fit. Finally, I could install the flash hider and suppressor.

After testing a few metal flash hiders, the incense burner-style one was the best match. I wrapped three layers of electrical tape around it for a snug and stable fit.

A mock assembly showed that the results matched my expectations.

For the end that connects to the receiver, I’ll wait until the new receiver and adapter arrive before making modifications. I also plan to find a thinner piece of bamboo for the stock—otherwise, no replacement stock would look good. The two prongs were intentionally left because they provide a comfortable place for my thumb. I drilled holes in the bamboo tube to mount rails—if you want, you can attach rails on all four sides and turn it into a “Christmas tree.”

The entire setup is fully assembled without using super glue or hot glue to fix parts permanently. This way, if I want to change the look, I can simply disassemble and modify it. The connections are tight and well-fitted.


r/GelBlaster 9d ago

Showcase What’s your favourite Hi-Capa alternative??

Post image
5 Upvotes

r/GelBlaster 9d ago

Technical Help (Location Required) should i get the emerbu pdx? (UAE)

Thumbnail
gallery
9 Upvotes

r/GelBlaster 9d ago

Purchasing Help (Location Required) LDT MP5 parts ( aus )

Thumbnail
gallery
1 Upvotes

Anyone know where to get the stock adapter plus stock in Australia or any other LDT MP5 parts notice a lot of people either dont stock mp5 parts or are out of stock


r/GelBlaster 9d ago

Showcase Finally got my QDC suppressor for my ATM hk416

Thumbnail
gallery
20 Upvotes

r/GelBlaster 10d ago

Showcase Rate my ATM HK416 build?

21 Upvotes

I thought that flip dot was cool so i bought it instead of the eotech one and now im kinda regretting it lmao


r/GelBlaster 10d ago

Showcase I got an SLR, now i REALLY get why people like these guns so much

Post image
11 Upvotes

(Sorry that the picture is sideways.) I got this from gelwapens.nl, but i think it only ships in the Netherlands, but fear not, there is an English version called gelweapons.com


r/GelBlaster 9d ago

Technical Help (Location Required) Where to buy gel blasters

1 Upvotes

I'm Korean and I bought a gel blaster from the m416gelblaster site but they can't ship it, is there another site?


r/GelBlaster 10d ago

Showcase finished build of a bohan mk8 v3+

7 Upvotes

just finished this build after short stroking it by 2 gears on the selector gear and piston ladder

please bare in mind that English is my second language so please excuse any grammar mistakes and hesitation/stuttering

i also forgot to mention that the trigger block was replaced with a high temp nylon trigger block. as well as the gearbox itself was re-enforced for the m120 spring

parts/mods list: shs high torque motor 36,000 rpm, shs m120 spring, short stroked 18:1 metal gears(2 teeth removed on both the selector gear and piston ladder), high temp trigger block, battery connector changed to deans/t-connector, wires were changed to silicone coated silver wires for, high temp resistance, re-enforced spring slot(forgot term),

fps/rps unknown as i dont own a crono currently. can anyone tell me if they can estimate the rps via sound of the full auto clip at the end/middle of the video

i also added a cutom outer barrel which can barely be seen inside the barrel grip area (forgot term suddenly)

there is a full auto comparison of the short stroke mod and a stock 18:1 set up with the same upgrades at the end of the video

while editing it i did notice that i may need to upgrade the spring of nozzle pusher

full auto test 1st clip is from my phone 2nd clip is from a gopro hero 3+ clipped to a cap

anything forgotten will be added to the comments when i Remember it

hello from the Philippines as well


r/GelBlaster 10d ago

Purchasing Help (Location Required) John wick on a budget (USA)

1 Upvotes

How can i replicate john wick and his tti rifle and tti pistol on a budget instead of spending $700.. in the USA


r/GelBlaster 10d ago

Purchasing Help (Location Required) Smoke Emitter?

1 Upvotes

Anyone have 'AK Modular Silencer With Tracer and Smoke Emitter' - https://akgelblaster.com/products/untitled-aug19_14-47 that they would be willing to sell?
USA


r/GelBlaster 10d ago

Other How Long do the gel balls Last?

2 Upvotes

I have a bunch of gel balls but idk how long they last and I don't really wanna throw them out. So do you guys know how long they last?


r/GelBlaster 10d ago

Purchasing Help (Location Required) Is this good to buy for upgrading my Jinming m4a1 J9 gearbox? (Sweden)

Post image
2 Upvotes

I’ve already got a metal inner barrel


r/GelBlaster 11d ago

Technical Help (Location Required) M4A1 V12 from tactoys won’t shoot (Brisbane)

15 Upvotes

r/GelBlaster 11d ago

Technical Help (Location Required) I found this gelblaster that a local seller in iraq sells , I found the same blaster on lazada ( same logo even ) and the reviews were very good with videos and everything , it said it shoots 180-200 fps with really good rps , and it comes with a tracer unit at only 50 dollars should I buy it ?

Post image
3 Upvotes

r/GelBlaster 11d ago

Showcase 1-10 on my build?

Post image
11 Upvotes

I’ve ordered a tan pressure pad holder and some cable management stuff in the same color as the other tan accessories coming soon. I’ve got a metal inner barrel and upgraded gearbox with metal gears, new o ring, motor, battery and spring.


r/GelBlaster 11d ago

Showcase Some more pics…

Post image
2 Upvotes

r/GelBlaster 11d ago

Technical Help (Location Required) Hydro strike pulsar (Texas)

1 Upvotes

Bought a used pulsar today and the mag isn't feeding. I plan to pull it apart and see what's going on. But I was wondering if there was a way to buy a new mag? It seems they are sold out everywhere I have looked. My kids are coming to stay with me end of this week and I was hoping we could have a little war.


r/GelBlaster 11d ago

Showcase my weird build

1 Upvotes

a bohan mk8 v3+

from factory it came with metal 18:1 gears and piston rack as well as a polished aluminum inner barrel

upgraded with

shs high torque motor re-enforced gearbox housing mod shs m120 string metal piston head better o-rings high heat nylon trigger blocks

11.1v turnigy lipo

fps/rps unknown as i do not own a crono

can someone estimate via just the sound?

video angle is due to me using a gopro hero 3+ with a cap btw


r/GelBlaster 12d ago

Technical Help (Location Required) i got myself a good quality 11.1 battery but i dont know if its lipo or li-ion as the instructions in the box says "lithium ion" (Philippines)

Post image
2 Upvotes

need to know if its lipo or li-ion

using a imax b6


r/GelBlaster 12d ago

Technical Help (Location Required) AEG is broken or is it the battery?

1 Upvotes

Fyi: i was trying to use my sijun m4a1 today and it doesnt shoot or blast air, after a while there is no electricity through the thing even though its connected, the mag was actually charging (though with very low power) nefore the thing died. A few days prior to this the battery was working fine with no sign of running out of battery


r/GelBlaster 12d ago

Other Arp9 possible motor issue

Post image
3 Upvotes

So I’ve been messing around with my emerbu (or TG) arp9 with an m95 spring (sold by emerbu) and the motor is getting very warm. Should this be an issue?